Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Inglewood
Gate installation in Inglewood runs $1,400 to $9,800 for a complete driveway gate, motor, and posts, with most single swing gates landing between $2,200 and $4,600. We install and warranty the full package: gate frame, hinges, post footings, operator, safety edges, and keypad. Ironworks Gate Co. has been building and hanging gates for over 42 years, and our crews know Inglewood’s older lots, narrow driveways, and coastal air better than any general contractor ever will. Call (747) 340-9707 for a free measure and a written price before anything gets ordered.
Why Ironworks Gate Co. Is Inglewood’s Preferred Gate Installation Company
Inglewood homeowners do not call us first because we are the cheapest. They call because someone before us hung a gate that sagged, or wired an opener that died in eighteen months, and they do not want to pay for that twice. Victor Salinas leads a crew that welds, sets posts, runs power, and programs operators in one visit, on one schedule. The job is quoted up front and agreed before a single bolt is turned. No surprises on the bill, no third truck showing up next week to finish what the first one started.
We work on homes from Hyde Park to Morningside Park, from La Brea Avenue east to Crenshaw. A call before noon gets a technician to most Inglewood streets the same day for emergency gate failures, and every completed installation carries our written 90-Day Done Right Promise. If it is not right, we come back and make it right. No paperwork, no arguing.
Gate Installation at Ironworks is not a side trade. It is the entire trade. That focus is why our technician on a swing gate near Darby Park last month spotted a cracked weld at the post base that another bid had missed, reinforced it before hanging the new panel, and saved the owner a second repair inside a year. That is the difference between a gate installer and a gate company.
Our Gate Installation Services in Inglewood
Driveway Gate
Most Inglewood driveways are narrow, built for a single car and a short approach. That means the gate must open cleanly without swinging into a sidewalk or a neighbor’s hedge line. We measure the actual setback, set posts in concrete below the root zone of whatever is planted nearby, and hang the gate so it clears grade by at least two inches on the swing side. A driveway gate in Inglewood typically runs $2,200 to $6,500 installed with a motor, depending on width, material, and opener brand.
Swing Gate
Swing gates remain the most common choice on Inglewood’s post-war bungalow lots because they match the original architecture and do not require a long track run. The issue here is the marine layer. Hinge pins that lasted forty years in Corona del Mar will shear in fifteen in Inglewood if they are painted steel. We spec stainless pins and galvanized hinges on every swing gate we install in this city. Expect $1,800 to $5,400 for a single swing gate with an operator, installed.
Pedestrian Gate
A pedestrian gate is the gate you actually use every day, which means it takes the most abuse. We build and install pedestrian gates in Inglewood with reinforced corner gussets and self-closing hinges where lot lines run tight to the house. These gates see constant latch cycling, and we set them so the latch catches without slamming, day after day. A new steel pedestrian gate with hardware runs $600 to $1,900, depending on width and finish.
Sliding Gate
Sliding gates make sense on Inglewood lots where the driveway slopes or where a swing gate would block the sidewalk. They run on a ground track that must be set level and kept clear. On event days near SoFi Stadium, we have seen slide tracks bent by cars that rolled forward too far while waiting for parking. We install heavier-gauge track and set the operator board in a sealed housing to handle both the salt air and the traffic. Sliding gate installations in Inglewood typically run $2,800 to $8,000 with automation.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Inglewood
We are certified and equipped on nine opener brands, and our Inglewood trucks carry parts for the ones we see most often on this side of the 405: Linear, Viking, Ghost Controls, and DoorKing. That matters when an operator board fails the morning after a big game and the gate will not close. We do not have to order a board from a warehouse and come back next week. In most cases the part is on the truck, and the gate is running before lunch. Whatever brand is on your driveway, one visit is the goal, and it is the standard we hold ourselves to.
Common Gate Installation Problems We See in Inglewood Homes
- Rotted hinge posts at the concrete line. Inglewood sits about five miles from the Pacific, and the marine layer that pushes in from El Segundo carries enough salt to eat through painted steel posts in fifteen to twenty years. When we hang a new gate, we set galvanized posts in deeper concrete and wrap the base so water cannot sit against the steel.
- Sheared hinge pins on 1950s wrought iron. Original gates on post-WWII bungalows were built with plain steel pins. After sixty years of coastal moisture, those pins snap, and the gate panel drops and drags across the driveway. The fix is a new stainless pin set and a frame correction, done before the new operator gets mounted.
- Gate operators damaged by event crowds. On game and concert days at SoFi Stadium, residential streets flood with foot traffic and cars. We routinely get calls the morning after because a latch was forced, a slide track got bent, or an opener board burned out from repeated cycling. An operator rated for heavy-duty cycling and a reinforced latch are the difference here.
- Undersized operator boards for coastal conditions. Moisture works its way into control boards that are not sealed well, and the salt accelerates the damage. We install operator housings with gaskets and use marine-grade connectors on every new gate in Inglewood, not just the ones within sight of the coast.
Pricing for Gate Installation in Inglewood, CA
You will see cheap gate ads in Inglewood. We are not one of them, and here is why. A single swing gate with a motor starts around $2,200 and runs to $5,400 depending on width and material. A sliding gate with a track and operator runs $2,800 to $8,000. A pedestrian gate costs $600 to $1,900. A full double driveway gate with new posts, two operators, and access control runs $5,500 to $9,800. Everything is quoted in writing before we start, and the price we agree on is the price you pay. We do not pad the bill after the fact, and we do not quote low to get the job and then “discover” a problem in the middle. Call (747) 340-9707 for a free measure in Inglewood and a firm, written number.
| Gate Type | Typical Inglewood Range |
|---|---|
| Pedestrian Gate (steel) | $600 - $1,900 |
| Single Swing Gate with Operator | $2,200 - $5,400 |
| Sliding Gate with Track and Operator | $2,800 - $8,000 |
| Double Driveway Gate, New Posts, Access Control | $5,500 - $9,800 |
Key takeaways: Post replacement is the most common additional cost on older Inglewood homes. Galvanized hardware adds roughly 10% to a job and doubles the life of the hinges near the coast. And any new operator should be rated for heavy-duty cycling if you live within a mile of SoFi Stadium.
We Also Serve Cities Near Inglewood
Our crews cover Gate Installation in Inglewood and the surrounding South Bay corridor, including Hawthorne, El Segundo, Culver City, and Lawndale. If you are in one of those cities and your gate is failing, call (747) 340-9707 and we will get a technician out on the same schedule we run for Inglewood.
Serving Inglewood, CA - Our Local Coverage Area
We’re based in the Inglewood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Inglewood
Inglewood sits roughly five miles from the Pacific, and the marine layer that rolls in from El Segundo and Playa del Rey carries salt and moisture that settles on metal surfaces overnight. That salt-laden air accelerates corrosion at the concrete line, where water wicks up into the post base and cannot evaporate quickly. On a painted steel post, that means rust-through in fifteen to twenty years. On galvanized or stainless hardware, the same location holds up for thirty to fifty. Call (747) 340-9707 and we will tell you what is actually installed on your gate and what it will take to make it last.
Yes, in most cases. Homes within a mile of SoFi Stadium see foot and vehicle traffic on event days that forces latches, bends slide tracks, and cycles operators dozens of times in a few hours. A light residential operator will burn out fast under that load. We recommend heavy-duty cycling ratings and a reinforced auto-close latch for any Inglewood home inside that radius. The cost difference is roughly $150 to $300 and it is the difference between a gate that works for a decade and one that fails the morning after the next home game.
For Inglewood’s marine layer, galvanized steel is the better base material. Painted iron can look beautiful for the first few years, but unless every weld is ground smooth and the finish is reapplied every few years, the salt air will find the thin spots and start rust bleeding through the paint. We build gates in galvanized steel and then powder-coat or paint over the galvanizing for appearance. That combination gives you the classic look without the fifteen-year rust-through problem. Expect galvanized to add about 10% to the gate cost, and to last twice as long.
The hinge assembly fails first, and then the operator board. Hinges take the full weight of the gate plus decades of salt exposure at the exact point where moisture collects. Once a hinge pin shears or a post rots at the base, the gate sags, drags, and puts a constant strain on the operator motor, which burns out the board. On a new installation near the coast, we replace steel hinge pins with stainless, set galvanized posts in deeper concrete, and seal the operator board housing. That order of protection addresses the failures in the order they actually happen here.
A stainless-steel hinge set on a galvanized post in Inglewood should last thirty to forty years before needing replacement, compared to fifteen to twenty for painted steel. The operator is a different story: electronics age faster than metal. Expect a good operator board to last ten to fifteen years in Inglewood’s marine air if the housing is sealed and the gate is balanced correctly. A gate that is out of balance will kill a board in three to five years. That is why we true and level every gate before mounting the operator, every single time. Call (747) 340-9707 for a free estimate on a new gate or a correction on the one you already have.
Call Ironworks Gate Co. for Gate Installation in Inglewood
If your gate is dragging, rusting through, or not closing the way it used to, call (747) 340-9707. A live person answers, day or night. We will schedule a free measure, give you a written price for the whole job, and hang a gate that is built for Inglewood’s salt air and SoFi traffic. Done right, backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Inglewood and the South Bay since 1984.