Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Florence-Graham
Gate motor and opener work in Florence-Graham usually runs $220-$640 depending on the opener type, the condition of the posts, and whether County permits come into play. Most motor repairs we handle in Florence-Graham are completed the same day we arrive, and we stock parts for the brands homeowners here actually have on their gates. If your gate stopped opening this morning on Compton Avenue or moved halfway and reversed, call (747) 340-9707 and a live person picks up. We have been doing this work since 1984, and Gate Motor & Opener in Florence-Graham is a route we run every week.
Florence-Graham is different from nearby incorporated cities, and that matters when you are replacing a motor or opener. The area’s unincorporated LA County status means permits and inspections route through the LA County Department of Public Works, not a city building department. Any gate motor or opener installation that touches a public right-of-way or requires structural changes to a post footing must be permitted that way. A lot of the gates here were installed decades ago without permits at all, so new motor work often forces a full code-compliance upgrade of posts, footings, and entrapment protection. You need a company that knows how that process works, not one learning it on your driveway.
Why Ironworks Gate Co. Is Florence-Graham’s Preferred Gate Motor & Opener Company
We carry the reputation of a company that has been welding and wiring gates for over 42 years, founded in 1984 under Victor Salinas. Homeowners in Florence-Graham call us because they want the correct fix on the first visit, not a sequence of return trips. Our technicians are background-checked, uniformed, and guided by the K.E.Y.S. values code: Krafted right, Every time, Your home first, Standing behind it. The 400th job gets the same care as the first.
Response time to Florence-Graham is usually same-day for motor repairs. Our dispatch and scheduling are coordinated from the brand’s Los Angeles office, and crews serve Florence-Graham locally. When a slide opener stops midway on a 1950s bungalow off Compton Avenue, we do not tell you to wait until Monday.
Every completed job is protected by the 90-Day Done Right Promise, a written guarantee with no paperwork and no arguing. If it is not right, we come back and make it right. You will know the price before a single bolt is turned. That is how Victor has run Ironworks Gate Co. from the start, and it is why homeowners in Florence-Graham who have been let down before tend to stay with us.
Our Gate Motor & Opener Services in Florence-Graham
Our Gate Motor & Opener team handles the full scope: repair, installation, automation, and upgrades on swing and slide gates. Here’s what we do most often in Florence-Graham, and what it looks like on the ground here.
Motor Installation in Florence-Graham
A new gate motor installation in Florence-Graham typically runs $350-$850 for the opener itself plus $400-$900 in labor and hardware, depending on gate weight, post condition, and whether new conduit or wiring is needed. On many 1940s and 1950s properties here, the original posts are set in cracked concrete pads that have shifted over decades. That means a proper installation is rarely a bolt-on job. We check the footing, the hinge line, and the gate’s travel before we ever open the motor box. If the post has to be replaced to make the operator work correctly, we tell you that before the price is set, and the price is agreed before work starts.
Motor Repair in Florence-Graham
Most motor repairs in Florence-Graham fall between $180 and $460. Common jobs include replacing a stripped gearbox, swapping a failed control board, resetting limit switches, or fixing a clutch that slips on a sagging gate. We carry parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we do not have to order and return a week later. If your opener hums but doesn’t move, or the gate reverses mid-travel like the one we fixed off Compton Avenue, we can usually diagnose and repair it in one visit.
Linear Motor Service in Florence-Graham
Linear arm operators are common on the tubular steel swing gates that front so many Florence-Graham bungalows. A linear motor replacement here typically runs $300-$650 including the part and labor. These motors work fine when the gate is balanced, but on older properties where the gate has sagged, the linear arm takes the full brunt and the motor burns out early. We check the gate’s weight and hinge alignment before installing a new linear motor, because putting a new motor on a dragging gate just means you will be calling again in a year.
Slide Motor Service in Florence-Graham
Slide gate openers run $400-$800 for replacement in Florence-Graham, more if the rack or the post footing has to be redone. Slide gates are common here on properties with concrete driveways and small frontages. The old 1940s concrete here shifts, and when the post footing tilts even a few degrees, lateral load transfers to the motor gearbox and the rack and pinion teeth start stripping. That is a Florence-Graham failure pattern we see weekly. We do not just swap the motor. We check the rack, the track, the rollers, and the post.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Florence-Graham
We are trained and equipped on nine gate-automation brands, and the ones we see most often on Florence-Graham driveways are BFT, Linear, Viking, and Ghost Controls. We stock local parts for these brands for Florence-Graham customers, which keeps turnaround fast. Whether you have an old Viking swing arm on a 1950s bungalow or a newer Ghost Controls opener on a rental property near the Florence-Firestone border, we know the wiring, the limits, and the failure points. Certified service across nine brands means the correct fix on the first visit, whatever is on your driveway.
Common Gate Motor & Opener Problems We See in Florence-Graham Homes
- Control boards shorting from trapped condensation. Summer mornings in Florence-Graham bring marine-layer humidity that sits on uncoated metal, and old cast-iron operator housings without weep holes trap moisture against the board. When the board shorts, the opener either doesn’t respond or triggers randomly. We add weep holes, seal the housing, and replace the board if needed.
- Slide gate rack and pinion teeth stripping. When a 1940s driveway shifts and the post footing tilts, the gate puts lateral load on the motor gearbox. The teeth strip, the gate jumps, and eventually the opener won’t move the gate at all. Fixing this properly means addressing the footing, not just swapping the rack.
- Swing gate hinge posts rotting below grade. Decades of irrigation overspray plus the area’s salt air exposure rot the buried section of hinge posts. The gate sags, the motor clutch slips, and the gate fails to latch. A new post, set in a County-compliant footing, solves it permanently.
- Thermal fatigue on gate hardware from afternoon heat. Florence-Graham’s inland position means afternoon heat spikes hit harder than coastal LA. Metal cycles daily, and on gates that haven’t been repainted in years, joints crack and hardware loosens. A seasonal tune-up catches this before the motor fails.
Pricing for Gate Motor & Opener in Florence-Graham, CA
A typical gate motor repair in Florence-Graham runs $180-$460, and a full motor replacement ranges from $300 for a basic linear arm to $850 for a heavier slide opener with new rack and wiring. What changes the number is gate weight, post condition, whether the footing is compliant, and whether a permit is required. Add a battery backup and you’re looking at $350-$650 extra, depending on the existing operator and whether it can accept the retrofit. All of this is quoted and agreed before any work starts, and the bill won’t surprise you. Estimates are free. Call (747) 340-9707 and we’ll walk the gate with you.
We Also Serve Cities Near Florence-Graham
Beyond Florence-Graham, our crews cover Inglewood, Westmont, Hawthorne, and West Athens regularly. If you are just across the county line or a few blocks over, the same team, the same written guarantee, and the same response time apply.
Serving Florence-Graham, CA - Our Local Coverage Area
We’re based in the Florence-Graham area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Florence-Graham
No permit is required for a straight motor or opener swap when the posts, footings, and gate structure remain untouched. The County requirement kicks in when the work touches a public right-of-way or when a post footing has to be replaced. A surprising number of Florence-Graham gates were built without permits decades ago, so when a footing finally fails and we have to pour a new one, the job gets brought up to current LA County Department of Public Works code as part of the repair. Call (747) 340-9707 and we’ll tell you exactly what your specific gate needs.
Condensation trapped inside the operator housing is the usual cause on Florence-Graham properties. The marine layer sits on uncoated housings overnight, moisture collects on the control board, and the opener faults out mid-travel until the housing dries. Old cast-iron operators mounted without weep holes are the worst offenders. The fix is to drill weep holes, seal the housing, and replace the board if it has already shorted. We see this every summer on gates off Compton Avenue and throughout the unincorporated county area.
Yes, in most cases a retrofit battery backup can be wired in, though the method depends on the operator’s board and power supply. Older DoorKing and Elite units sometimes need a separate battery tray and charger wired on the DC side rather than a plug-in module. We have done these retrofits on Florence-Graham gates where the homeowner wants the gate to open during an outage, and the 90-Day Done Right Promise covers the work either way. Call for a free estimate and we’ll confirm what your specific opener can accept.
If the hinge post is rusted through below grade, tightening the hinges won’t hold. On Florence-Graham’s older properties, irrigation overspray and salt air rot the buried section of the post, and the gate drops just enough to make the motor clutch slip and grind. In that case the post comes out, we pour a new County-compliant footing, set a new post with stainless fasteners, and re-hang the gate to line. If the post checks out solid and the sag is from worn hinges alone, we replace the hinges. We always tell you which one it is, and the price is set before we start.
Yes. Florence-Graham sits close enough to the coast that marine-layer humidity and salt air accelerate corrosion on uncoated steel and iron gate hardware. We specify galvanized or powder-coated posts and stainless fasteners on motor and opener work here because painted steel rusts out in a few years. Control housings need weep holes and sealed gaskets to keep condensation off the board. These are not upgrades for show. They are the difference between an opener that runs for five years and one that fails every summer. When you call (747) 340-9707, ask us about corrosion-mitigating hardware for your specific gate.
Call Ironworks Gate Co. for Gate Motor & Opener Work in Florence-Graham
If your gate motor is grinding, reversing, or dead, call (747) 340-9707. A live person answers, 24 hours a day, 7 days a week, not a voicemail tree. We’ll ask about your gate, give you a straight range over the phone, and schedule a visit. The price is quoted and agreed before any work starts. Every job we do in Florence-Graham is backed by the 90-Day Done Right Promise in writing. Done right, and backed up. That’s the deal, and it has been since 1984.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Florence-Graham and surrounding communities with gate automation since 1984.