Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Installation in Inglewood: What to Know First
Ghost Controls gate installation in Inglewood typically runs $850 to $2,400 depending on whether you need a new opener mounted on an existing gate, a full gate-and-opener package, or a replacement for a failed unit. We complete most Ghost Controls installations in a single visit, and as an independent Ghost Controls service provider, we quote the full price before any work begins. If you own a Ghost Controls opener and the gate isn’t moving right, call (747) 340-9707 for a free estimate.
This page is for Inglewood homeowners who already bought Ghost Controls equipment, or are considering it, and need a gate specialist who actually knows the brand. We’re Ironworks Gate Co., and we’ve been working on driveway gates in this city for over 42 years.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls makes solid openers, but we see the same handful of problems repeat across Inglewood driveways. Here’s what actually goes wrong and what we do about it.
- AXDP and AXD series: control board relay burnout. Inglewood’s marine-layer mornings mean damp, salty air sitting on exposed circuit boards. The AXDP’s relay contacts oxidize, and the gate stops responding to remotes even though the motor still hums. We replace the board with a factory or quality aftermarket unit and seal the housing properly, which the original install often wasn’t.
- Gate arm bracket fatigue on double gates. Ghost Controls arms are strong for their class, but on wide double gates in neighborhoods like Ladera Heights and Morningside Park, the bracket bolts loosen under repeated wind loading from the afternoon sea breeze coming up La Cienega. We re-tap, install backing plates, and torqued to spec, so you’re not re-tightening bolts every three months.
- Limit switch drift after power flickers. Inglewood gets brief outages during Santa Ana season, and Ghost Controls units with older firmware can lose their travel limits when power returns. The gate then slams against the open stop or stops six inches short of closed. We reset travel, check the full mechanical sweep, and update any firmware that allows it.
- Battery backup kits installed wrong. The Ghost Controls GTO battery kit is a good idea, but we regularly find them wired with undersized spade connectors that arc and melt under load. We re-terminate with proper gauge connectors and heat-shrink, then test the full open-close cycle on battery alone. The fix takes an hour; the melted harness if left alone takes out the control board.
- Chain drive slack on older models. Ghost Controls made chain-driven arms for years, and the chain stretches. Owners keep calling about grinding noise and a gate that bounces at the ends. We tension the chain to factory spec and check sprocket wear before it rounds off and skips. Replacement drives, if needed, come as a bolt-on kit without replacing the whole opener.
Our Ghost Controls Gate Installation Process
Every Ghost Controls job follows the same sequence, whether it’s a new install in Inglewood or a replacement that failed after another company left. We do it the same way every time because it works.
- 1
Call and conversation. A live person answers at (747) 340-9707. We ask about your gate type, opener model, and symptoms, then schedule a time that works for you.
- 2
On-site inspection. Our technician checks the gate itself first: hinges, welds, travel path, post stability. A new opener on a sagging gate is wasted money, so we fix the gate before we touch the motor.
- 3
Straightforward quote. We give you a written price for parts and labor before any work begins. You approve it, we do it. If the job changes, the price doesn’t without your say-so.
- 4
Installation. We mount the Ghost Controls arm or ram, run power correctly, set limits, and program remotes and keypads. We use OEM parts where it matters most: control boards, safety sensors, and gear assemblies.
- 5
Full cycle test and cleanup. We run the gate through open-close cycles at least a dozen times, adjust force settings so it stops if it meets real resistance, then leave the area cleaner than we found it.
- 6
90-Day Done Right Promise. Every Ghost Controls installation comes with our written guarantee. If something isn’t right, we come back and make it right. No forms, no phone tag, no arguments.
What Ghost Controls Gate Installation Costs in Inglewood
Here are the dollar ranges we quote most often on Ghost Controls work in Inglewood, based on what we’ve seen over the years.
| Job Type | Typical Cost Range |
|---|---|
| Single swing gate, new Ghost Controls opener install | $850 – $1,450 |
| Double swing gate, dual-arm Ghost Controls install | $1,400 – $2,400 |
| Sliding gate, Ghost Controls conversion kit | $1,100 – $1,900 |
| Replacement control board or motor on existing install | $380 – $860 |
| Full pedestrian gate with Ghost Controls opener | $1,200 – $2,000 |
What moves the price is the condition of your existing gate, the distance from your electrical panel to the gate post, and whether we’re dealing with rust on the hinge points. Every estimate is free, and the number we quote is the number you pay. Call (747) 340-9707 and we’ll come out and look.
Why Inglewood Homeowners Call Ironworks Gate Co. for Ghost Controls Work
We’re not the only company that touches gate openers in Inglewood, but we’re the one people call when they want it done right once. Victor Salinas grew up in Morningside Park, and for over 42 years Ironworks Gate Co. has worked on gates in this city with a simple rule: do the job as if our own mother has to pull into that driveway tonight.
Ghost Controls is one of nine opener brands we service, alongside LiftMaster, Mighty Mule, and DoorKing. That matters when a Ghost Controls unit should honestly be replaced with something sturdier, or when you have a mixed setup with a Ghost Controls board and LiftMaster arms. We tell you what’s worth saving and what isn’t, and we stand behind the call in writing with our 90-Day Done Right Promise. A live person answers the phone 24/7, not a voicemail tree. We’ll be there when we say.
We do it right once, so you do not have to call twice.
FAQs
No, using an independent installer does not void your Ghost Controls manufacturer warranty, which is good news for Inglewood owners who prefer a local specialist over whoever the big-box store sends out. We install to Ghost Controls factory specifications and use OEM components for warranty-covered parts. What does void warranties is improper power wiring or forced motor operation, both of which we check for on every job.
Yes, we install Ghost Controls openers on gates built by other companies every week in Inglewood. The key is checking the gate’s weight, hinge condition, and post alignment before mounting the opener, because a gate that drags on its hinges will burn out any motor in under two years. We fix the gate first, then attach the Ghost Controls unit.
In most cases, we can have a Ghost Controls gate operational the same day we arrive, because our trucks carry common Ghost Controls parts including boards, remotes, and limit switches. For parts we don’t have on hand, typical wait is two to four business days. Call (747) 340-9707 and tell us what the gate is doing, or not doing, and we’ll tell you straight what to expect.
If your Ghost Controls opener is under ten years old and the issue is a board, limit switch, or remote receiver, repair is usually the right call and runs $380 to $860 in Inglewood. If the motor itself has seized or the gearbox is grinding, replacement typically makes more sense. We’ll give you an honest answer either way, and the quote is free.
Yes, every Ghost Controls installation we do includes the full electrical scope: power from your panel to the gate post, properly buried conduit, safety photo eyes, and any required ground-fault protection. Many Inglewood homes built before 1990 have older panels, and we verify the circuit can handle the opener’s startup draw before we mount anything. Call (747) 340-9707 for a free estimate on the complete installation.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Inglewood and nearby areas.