Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Access Control Installation: The Inglewood Owner’s Guide
Ghost Controls access control installation in Inglewood typically runs $340 to $780 installed, including the replacement part, wiring verification, and full system testing before we leave the driveway. We stock Ghost Controls-compatible keypads, receivers, and vehicle sensors on our trucks, so most access control replacements are completed in a single visit, often the same day you call. The way most homeowners discover the part has failed is quiet and gradual: the keypad still beeps but the gate doesn’t move, the remote works from 20 feet but not 40, or the gate opens on its own in the middle of the night for no reason anyone can find.
Which Ghost Controls Models This Applies To
We install and service access control across the Ghost Controls line, including the AXP series (AXP1, AXP2), the TSS1 and TSS1XP solar-capable openers, and the DTP1 dual-gate systems. The access control components these systems use vary by model year, and this is where we see compatibility mistakes happen most often. The keypad part number stamped on the back housing needs to match your control board revision, not just the Ghost Controls name on the front. A keypad from a 2017 AXP1 will not always talk to a 2021 control board without a receiver swap. We check the board revision and the part label before anything gets wired in. On the OEM versus aftermarket question: Ghost Controls OEM access components are well built, but they are not the only option. We stock both OEM and quality aftermarket receivers and keypads that meet or exceed the original specs, and we will tell you honestly which makes sense for your gate. An aftermarket receiver with a wider temperature tolerance often outlasts the OEM unit in Inglewood’s summer heat, where surface temperatures on a south-facing keypad post can hit 140 degrees in August.
Signs Your Ghost Controls Access Control Installation Is Failing
- The keypad beeps but the gate won’t move. The keypad’s internal relay is firing, but the signal isn’t reaching the control board. This is usually a failing receiver module or a corroded connection at the board, not the keypad itself.
- Range on remotes drops from 40 feet to 10 or less. Ghost Controls receivers degrade in direct sun and coastal air over time. Once you are standing next to the gate pressing the button three times, the receiver has lost its sensitivity and needs replacement.
- The gate opens by itself, usually at night. A failing receiver can pick up stray RF interference from nearby garage door openers, alarm systems, or even passing trucks with certain radio equipment. We have traced this exact problem to three different Inglewood blocks in the last year alone.
- The external keypad works only in cold weather, or only in warm weather. Thermal expansion inside the keypad housing cracks solder joints on the circuit board. What looks like a programming issue is almost always a physical failure inside the keypad.
- The control board shows error codes after a storm or power outage. Power surges through the access control wiring are common in Inglewood during Santa Ana season. When the board throws codes after every brownout, the surge protection on the access line has already failed.
Replacement Cost & What’s Included
For Ghost Controls access control installation in Inglewood, a single keypad replacement runs $180 to $320 installed. A receiver replacement or addition runs $160 to $280. A full access control refresh, meaning keypad, receiver, and reprogramming of all remotes, runs $340 to $510. If you are adding a vehicle sensor loop or a phone-based access module, that pushes the job to the $600 to $780 range. Every quote we give includes the part at our cost plus labor, and the price is settled before a single bolt turns. You will not see a surprise line item. The labor includes removing the old component, checking the wiring run for damage, installing the new unit, and testing every remote, keypad, and safety input on the system. All of it is covered by our 90-Day Done Right Promise in writing.
DIY or Call Us?
Access control work on a Ghost Controls system is low-voltage, so the danger is not electrocution. The danger is misdiagnosis. We regularly get calls from Inglewood homeowners who replaced a $200 keypad only to find out the actual problem was a $60 receiver inside the control box. Ghost Controls keypads, receivers, and boards are matched by revision, and guessing wrong costs more than the part itself. What you can safely check yourself: press the keypad buttons and note exactly what happens. Does the backlight come on? Does it beep once or three times? Does the gate click but not move? That detail saves a service call, and we are glad to work through it with you over the phone. Victor Salinas has been doing this long enough to know that a homeowner who calls and says exactly what the keypad did this morning gets their gate fixed faster than the one who already ordered the wrong part online. Call (747) 340-9707 and we will talk through what you are seeing. If it turns out to be a simple fix you can handle, we will tell you that too. We would rather earn the next job than sell you a part you don’t need.
FAQs
Five to eight years in our experience. Inglewood’s sun exposure and temperature swings shorten that on south-facing or west-facing posts. Keypads mounted in direct afternoon sun fail at the circuit board level faster than shaded ones. If yours is past seven years old and acting up, replacement is usually cheaper than repair.
Most of the time, no. The failure is inside the sealed circuit board, where solder joints crack from thermal cycling. We can reflow a cracked joint occasionally, but the repair is not reliable for more than a few months. A new keypad with a written guarantee is the honest fix. Call (747) 340-9707 and we will price it for your exact model before we schedule.
A single keypad or receiver replacement is typically done in 45 to 90 minutes, including testing all existing remotes and reprogramming. A full refresh with multiple components takes two to three hours. We carry the common Ghost Controls access parts on the truck, so there is rarely a second visit.
We stock Ghost Controls-compatible keypads, receivers, and sensors on our service trucks, along with parts for LiftMaster, Mighty Mule, and DoorKing systems. If your system needs a less common component, we order it and return for installation once it arrives. We will always tell you upfront if a part is not on the truck before we schedule.
If your Ghost Controls access control is failing in Inglewood, call Ironworks Gate Co. at (747) 340-9707. A live person answers, day or night, and we will give you an honest price before any work begins. We do it right once, so you do not have to call twice.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Inglewood and nearby areas.