FAAC Gate Motor Replacement Nationwide

FAAC Gate Motor Replacement: The Inglewood Owner’s Guide

FAAC gate motor replacement in Inglewood typically runs $850-$2,400 installed, depending on the model and whether you need a full arm-and-motor assembly or just the operator head. We stock FAAC-compatible replacement motors on our trucks and can usually complete the swap in a single visit. Most Inglewood homeowners discover the failure the hard way: the gate groans halfway open, stops responding to the remote, or sits dead after a rainstorm, leaving the driveway inaccessible.

Call (747) 340-9707

FAAC builds its operators differently than most American brands. The motors are hydraulic, not mechanical, which means when they fail, they fail gradually rather than snapping outright. You’ll notice sluggish movement first, then intermittent operation, then nothing. By the time most owners call us, the motor has been limping along for weeks.

Which FAAC Models This Applies To

We replace motors on the full FAAC swing-gate and slide-gate lineup you’ll find on Inglewood driveways: the 400 Series (402, 412, 422), the 750 and 770 slide operators, the C720 and C721, and the newer E024S and S418 swing arms. The compatibility gotcha most owners miss is that FAAC changed the motor mounting pattern between the 400 and 400 R-series, so a used motor from an older unit will not bolt onto a newer chassis without an adapter plate we fabricate in-house.

Identify your model by the silver data plate on the operator housing, usually on the underside or inside the release hatch. It lists the model number and hydraulic spec. FAAC OEM motors are well built, but for units over ten years old, a quality aftermarket equivalent often makes more sense: same housing dimensions, same hydraulic output, roughly 30 percent lower cost. We carry both and will tell you plainly which one suits your gate and your budget. Ironworks Gate Co. is an independent gate specialist, not a FAAC dealer, so our recommendation is based on what works, not what we’re obligated to sell.

We also stock replacement parts for LiftMaster, Mighty Mule, and Ghost Controls operators if you’re weighing a full system swap.

Signs Your FAAC Gate Motor Replacement Is Failing

• Sluggish opening or closing. Hydraulic fluid breaks down over time, especially in Inglewood’s summer heat. The motor works harder, runs hotter, and moves slower. This is the earliest warning sign.
• Intermittent response to remotes and keypads. Before the motor dies outright, it often becomes harder to start. The capacitor or internal windings are degrading. You’ll find yourself pressing the remote twice, three times.
• Humming with no movement. A motor that hums but doesn’t turn is telling you the start capacitor has failed or the pump has seized. Continuing to press the button burns out the windings completely.
• Burning smell or visible oil seepage. FAAC motors are sealed hydraulic units. Oil around the housing or a hot electrical smell means the internal seals have given out. This is not a repair-item situation; it’s replacement territory.
• Gate stops mid-travel and reverses. The motor’s torque output drops as it fails, tripping the obstruction sensor prematurely. The gate thinks it hit something. It didn’t. It just ran out of strength.

Replacement Cost & What’s Included

Installed FAAC gate motor replacement in Inglewood falls into three bands. A basic 400 Series swing motor replacement runs $850-$1,400. Mid-range slide operators and heavier swing arms like the 750 or C720 run $1,300-$1,900. Full operator replacement with motor, arm, control board, and receiver runs $1,800-$2,400. The spread depends on gate weight, whether we’re swapping just the motor or the full assembly, and whether your existing control board is compatible with the new motor spec.

Every quote is itemized: parts, labor, and any adapter fabrication. We settle the price in writing before a single bolt is turned. You’ll never see an invoice bigger than the quote. The replacement itself is covered by our 90-Day Done Right Promise in writing: if it isn’t right, we come back and make it right.

DIY or Call Us?

What you can safely check yourself: whether the breaker for the gate is on, whether the release handle is engaged, and whether the control board shows a fault light. Those three checks take five minutes and tell you whether the problem is upstream of the motor. Beyond that, FAAC motor replacement is not a homeowner job. These are hydraulic units with 120-volt wiring and pressurized internal components. The motor swap requires discharging the system properly, matching hydraulic specs to gate weight, and re-bleeding the circuit. We have rebuilt gates in Inglewood where a homeowner’s partial attempt left the gate mid-travel and the motor irreparable. The fix cost twice what the original replacement would have.

If your FAAC gate motor is dead or dying, call us at (747) 340-9707. We’ll tell you over the phone whether it sounds like a motor, a board, or something simpler, and we’ll schedule a visit that works for you. A live person answers, day or night.

FAQs

Call Ironworks Gate Co. for FAAC Motor Replacement in Inglewood

Victor Salinas has been repairing and replacing gate motors in Inglewood for over four decades, since his grandfather’s welding shop in Morningside Park first taught him that patient work outlasts quick work. We do it right once, so you do not have to call twice. If your FAAC operator is failing or already dead, call (747) 340-9707 for a free estimate and a straight answer on what it will take to get your gate closing like the day it was hung.

Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Inglewood and nearby areas.